Dryer vent cleaning
Whole-home duct cleaning
Camera inspection
Sanitizing & deodorizingWhole-system duct and dryer vent check with before-and-after photos - you see exactly what came out of your vents
That "$99 whole-house special" is a bait ad - the real number appears once they are in your hallway, or the "clean" is a shop-vac at the register. We photograph the inside of your ducts before and after instead.
Trusted Dryer Vent Cleaning for Ventura Homeowners
A clogged dryer vent doesn’t just make your laundry take twice as long. It’s the leading cause of appliance-related house fires in the United States, according to NFPA data, and in coastal communities like Ventura the problem gets worse faster. Humid marine air causes lint to clump and adhere inside vent runs instead of blowing through, which means a vent that would function fine in Bakersfield can become a hazard here in half the time. We’re Air Duct Cleaning Ventura, led by Neil Fuentes, and we clean dryer vents the same way we clean duct systems: with commercial-grade equipment, verifiable results, and no shortcuts. Call (855) 507-7508 for a free estimate.
Dryer Vent Cleaning Service
Dryer Vent Cleaning Service is the process of removing built-up lint, debris, and obstructions from the entire exhaust run from your dryer to the exterior vent termination. In Ventura, where coastal moisture turns lint into a dense, sticky mat, this service typically runs $129 – $249 depending on vent length, accessibility, and how long it’s been since the last cleaning. We use the Rotobrush contact-cleaning system with Nikro HEPA filtration to physically agitate lint off the vent walls and extract it under negative pressure, not just blow it around.
Equipment That Makes a Difference
The Rotobrush system spins stiff nylon brushes against the vent walls while simultaneous vacuum extraction pulls loosened debris back to a HEPA-filtered Nikro unit. That combination means the lint leaves your vent entirely instead of getting pushed further down the run. Abatement Technologies containment protocols keep whatever we remove from re-entering your laundry room.
When You Should Schedule This
The NFPA recommends annual dryer vent cleaning for a typical household, but Ventura’s humidity often shortens that interval. If a load that used to dry in 45 minutes now takes 70, or if the laundry room gets noticeably warm while the dryer runs, the vent is already restricted. Homes with long vertical runs through the roof, or flexible foil ducting installed by the builder, tend to need attention more often than short horizontal runs with rigid metal pipe.
Styles & brands we work with
- Whole-home duct cleaning
- Dryer vent cleaning
- Camera inspection
- Sanitizing & deodorizing
Dryer Vent Installation
Dryer Vent Installation covers the design and fitting of a complete exhaust pathway: the transition duct behind the dryer, the run through the wall or ceiling, and the exterior termination with a proper backdraft damper. In Ventura, where many homes date to the 1970s and 1980s, we frequently see installations that predate current code requirements. Installation work here typically runs $225 – $450 depending on run length, materials, and access. Neil Fuentes and the team install rigid metal ducting with smooth interior walls, because corrugated foil holds lint and creates the exact blockage profile that leads to fires.
Code-Compliant Materials
California mechanical code specifies smooth-walled metal duct with a maximum run length of 35 feet before you must consider a booster fan. Each 90-degree elbow counts as five feet of effective length. We calculate effective distance on every install, not just the straight-line measurement, which catches problem layouts that foil-and-tape installers miss.
Replacing the Builder-Grade Stuff
Most homes in the Ventura area were built with white vinyl or foil flex exhaust duct. It fails in two ways: the vinyl sags and traps lint, and the foil tears easily at the connection points. When a vent has to pass through an attic or interior wall, rigid or semi-rigid metal is mandatory, and the joints must be sealed with metal tape, never drywall screws penetrating the airflow path.
Dryer Vent Repair
Dryer Vent Repair addresses damaged, disconnected, or improperly routed sections of the exhaust system without replacing the entire run. In Ventura, we commonly repair vents that have been crushed behind the dryer, separated at a splice point inside a wall cavity, or chewed through by rodents in the attic. Repair pricing typically falls between $150 – $350 depending on what section needs to be opened up and what the damage looks like. We treat every repair as a fire-prevention issue, not a handyman patch job.
Common Failures We Find
The single most frequent failure is a vent that has separated inside the wall or attic, which means the dryer is exhausting conditioned air, moisture, and lint directly into your home’s structure. That’s how you get mold growth in the wall cavity and a persistent musty smell no amount of cleaning will fix. Second on the list is a crushed transition duct behind the dryer, usually from the appliance being shoved back too hard after a clean-out.
When Repair Beats Replacement
If the vent run itself is properly sized and routed but has one bad joint or a damaged termination cap, repair makes more sense than a full re-install. We’ll tell you directly which one we’d recommend and why, including the cost difference. You won’t get an upsell here.
Dryer Vent Cleaning Company
A Dryer Vent Cleaning Company is only as good as the equipment it brings through your door and the technician running it. Air Duct Cleaning Ventura operates as a dedicated dryer vent cleaning company within a full-service duct operation: cleaning, repair, and installation handled by the same team under Neil Fuentes. That matters because a vent problem is rarely isolated. When we clean your vent we also check the transition duct, the termination damper, and the airflow path for damage that would undermine the work. You can expect $129 – $249 for a standard residential cleaning here in Ventura.
Why You Don’t Want a Franchise Special
The industry standard bait is a $49 or $79 coupon that becomes $400 once the tech “finds” a problem. We don’t play that. The price we quote over the phone is the price for the job, and if we find something damaged during the cleaning, you get documentation and a repair quote before any additional work happens. No pressure, no surprise invoice.
One Team for Duct and Vent Work
Because we also handle air duct cleaning and air duct repair, we understand the house as a system. A dryer vent that’s clean but connected to an HVAC return is still pulling dusty air through your living space. We can address the whole picture in one visit if that’s what the home needs.
Dryer Vent Inspection
Dryer Vent Inspection is a diagnostic service that evaluates airflow, vent material, routing, and safety compliance without performing a full cleaning. In Ventura, where slab foundations and tight utility closets make visual inspection difficult for homeowners, a professional inspection with the right tools costs $89 – $129 and takes about an hour. We use an inspection camera to document what the inside of your vent actually looks like, because “it seems fine” is not a safety standard.
What We’re Looking At
We measure static pressure and airflow at the exterior termination, which tells us whether the restriction is in the vent run, the transition duct, or the dryer itself. The camera footage shows us lint accumulation depth, joint separations, and any corrosion or pest damage. You get the report and can decide what to do next.
Who Should Get One
If you’ve just bought a home in Ventura or Oxnard, an inspection before you run a single load is cheap insurance. The previous owner’s maintenance habits are unknown, and the vent is hidden inside the wall. We also recommend inspection for anyone whose dryer has been functioning poorly for several months, since restricted airflow can also damage the dryer’s heating element and thermal fuse over time.
Commercial Dryer Vent Cleaning
Commercial Dryer Vent Cleaning services laundromats, apartment complexes, salons, restaurants, and any facility running dryers for hours each day. Usage volume matters more than building size: a salon doing multiple loads daily can clog a vent faster than a four-bedroom house. Commercial pricing in the Ventura area typically starts around $250 and scales with vent count, run length, and access difficulty. We quote each property individually after a walkthrough.
Multi-Unit and Property Management Work
For apartment buildings and HOA-managed laundry facilities, we provide per-unit vent cleaning with consistent documentation for your maintenance records. Property managers in Oxnard and Camarillo use our reports to demonstrate compliance with safety obligations. We schedule around tenant access requirements and work in occupied buildings without disruption.
Restaurants, Salons, and Care Facilities
Commercial dryers in these settings run back-to-back all day, often with towels and linens that shed heavily. The lint load is dramatically higher than residential, and we see vents in restaurants clog to fire-hazard levels in under six months. Our commercial process uses the same Rotobrush and Nikro equipment, but with extended run time and more aggressive brush configurations matched to the vent diameter.
Brands We Service
We service every major dryer brand, including Whirlpool, Maytag, LG, Samsung, Electrolux, GE, Speed Queen, and Kenmore. Most of the dryers we see in Ventura homes are Whirlpool or LG, and we’re familiar with the venting requirements each manufacturer specifies. A Samsung dryer’s airflow sensor, for example, will trip a “vent blockage” error at a lower restriction threshold than a Whirlpool, and that matters for diagnosing whether the vent or the machine is the problem.
We also work with commercial Speed Queen units in laundromat settings, where factory service intervals are frequent and documentation requirements are strict. Whether you have one of those or any other make, we can help.
See the difference
Before
After
Before
After
Before
AfterSigns You Need a Pro Right Now
- Clothes take more than one cycle to dry. This is your dryer telling you, through its own moisture sensor, that airflow is restricted. The heating element comes on, but the warm, wet air has nowhere to go, so it just circulates in the drum. Every extra cycle is more lint accumulating on the heating element, where it can ignite.
- The laundry room gets hot and humid while the dryer runs. That’s exhaust air leaking out of a separated or failed connection, not a quirk of the house. Moisture being pumped into the wall cavity behind a dryer is a mold problem in the making, especially in Ventura’s already-humid coastal environment.
- You smell burning or notice the dryer exterior is unusually hot. Lint is combustible, and when it accumulates around the heating element or blower wheel, the smell is often the first warning. Shut the dryer off and call us. This is not a symptom to monitor.
- The exterior vent flap doesn’t open when the dryer runs. That means airflow is too weak to push the damper open, or the damper is seized shut with lint and corrosion. Either way, your dryer is working against a blocked exit.
- It’s been more than a year since the last cleaning. You may not notice any of the above symptoms, but the accumulation is happening anyway. An annual cleaning is the recommendation from the NFPA, and it’s the single highest-value fire prevention step you can take in the laundry room.
Our Process, Step by Step
- 1
Arrival and setup. We arrive with the Rotobrush system, Nikro HEPA filtration unit, and Abatement Technologies containment materials. The dryer gets pulled out carefully, the transition duct inspected, and the work area protected.
- 2
Initial airflow measurement. Before we touch the vent, we hook up an airflow meter and record static pressure and velocity at the dryer connection and at the exterior termination. This gives us a baseline and helps locate the worst restriction.
- 3
Contact cleaning through the full run. The Rotobrush head spins through the entire vent while the Nikro unit holds the system under negative pressure. Lint is dislodged and extracted simultaneously, and the HEPA filter catches particulates down to 0.3 microns, so nothing re-enters the living space.
- 4
Verification and documentation. After cleaning, we re-measure airflow and record the difference. We also run the inspection camera through the vent if we haven’t already, so you can see the interior walls before and after. You get the numbers and the footage.
- 5
Final report and recommendations. If everything is clean and up to code, we’ll tell you that. If we found damage, improper materials, or routing problems, we’ll show you exactly where and quote a repair. No pressure, no mystery.
How Much Does Dryer Vent Cleaning Cost in Ventura?
A typical residential dryer vent cleaning in Ventura runs $129 – $249. The variance depends mostly on three things: vent length, access, and condition. A short, straight run through an exterior wall is on the lower end. A 25-foot run through the attic with two elbows, a roof termination, and a steep pitch is on the upper end. If the vent hasn’t been cleaned in years and the lint is heavily compacted, it takes longer and costs more. A Dryer Vent Cleaning in Ventura quote from us is always the full price for the job, agreed before we start.
If you’re comparing quotes, look for what’s included. Some companies quote a base rate and add per-vent or per-floor fees when they arrive. Others exclude the transition duct behind the dryer, which is where most blockages actually form. We quote one flat price per system, and the transition duct is always included. What affects the price on a legitimate quote: total vent length, number of bends, access difficulty like a second-story roof or tight attic clearance, and how much lint has accumulated. What shouldn’t affect it: how nice your neighborhood looks or what kind of car is in the driveway.
Inspection reports, camera footage, and airflow measurements are part of the service at no extra charge. The free estimate means we come out, look at the system, and give you a firm number before any work begins.
Our Service Area Near Ventura
We serve all of Ventura and the surrounding communities, including Oxnard, Camarillo, Santa Paula, Port Hueneme, El Rio, Ojai, Oak View, Mira Monte, and Fillmore. Coastal town, valley town, or hillside home, the vent problems follow the same patterns: marine moisture, aging construction, and deferred maintenance. We schedule service across the area every week and know the common vent configurations in each community.
Serving Ventura, CA – Our Local Coverage Area
We’re based in the Ventura area and know this community well. Use the map below to see our service coverage – if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Dryer Vent Cleaning in Ventura
Dryer vent cleaning is the removal of lint, dust, and debris from the full exhaust pathway between your dryer and the outside. It’s a fire-prevention measure and an efficiency service in one. A clean vent means your dryer runs shorter cycles, uses less energy, and doesn’t risk igniting the lint packed around its heating element.
A typical residential cleaning takes 60 to 90 minutes from setup to final report. Longer runs, roof terminations, or heavy buildup can extend that. We’ll give you a time estimate when we quote the job.
Plan on $129 – $249 for a standard residential system, with the price set before we begin work. Factors include vent length, number of elbows, access, and buildup. Call (855) 507-7508 and we’ll give you a firm quote for your specific home.
Yes. We service every major brand, including LG, Samsung, Whirlpool, Maytag, GE, Electrolux, Speed Queen, and Kenmore. The vent is independent of the dryer brand, but we know how each manufacturer’s airflow sensors behave, which helps us diagnose and verify.
If you smell burning or see smoke, stop running the dryer immediately and call us at (855) 507-7508. We treat that as a priority and will get a technician to you as fast as our Ventura schedule allows. Do not run the dryer again until the vent and the appliance are checked.
We stand behind the cleaning with before-and-after airflow measurements and camera documentation. If the vent isn’t clean, you can see it. We have a satisfaction guarantee on the work and will return to address any issue. Call for details on what’s covered.
Clear a path to the dryer and the exterior vent, and if you have pets, we appreciate them being secured. We handle moving the dryer, protecting the floor, and everything else. We’ll show you the before-and-after footage before we leave.
Schedule Your Dryer Vent Cleaning Service in Ventura Today
If your dryer vent hasn’t been cleaned in the past year, or if drying times are creeping up, don’t wait for the smell of burning to make the decision. Call Air Duct Cleaning Ventura at (855) 507-7508 to schedule a free, no-obligation estimate. We’ll inspect the system, show you the numbers, and quote a firm price. Neil Fuentes and the team are ready when you are.
Written by Neil Fuentes, Owner at Air Duct Cleaning Ventura, serving Ventura and surrounding communities.